Chuck Van Eekelen
Forum Replies Created
-
AuthorPosts
-
Chuck Van EekelenModerator
Bit of a waste having to use 16 channels per par if the fixtures have only 8 channels.
As I said, I use DMX software (with a mini-Moog midi controller attached). This gives me full control over anything and each fixture has it’s own channel settings.
I don’t ever recommend hardware controllers for DMX for this reason. You can probably get better results with something like Sound Switch.
I took a quick look at the manual and it’s not all that clear. Theoretically, you should be able to set the channel values per fixture and save those. By then selecting a fixture with a saved setting, it should do what you need. How exactly that would work with this particular controller is a question I unfortunately can’t help you with.
Chuck Van EekelenModeratorYou are welcome. The KRK’s you linked to are 10″!!! and 3-way instead of 2. So very logical they are expensive.
I can see the size issue. As for the KRK’s being “reference” monitors, they can provide plenty of loud when used as nearfield speakers (i.e. less than 3 feet from your ears). But if you play them loud for too long your can experience some ear fatigue of course.
Chuck Van EekelenModeratorWhat you describe would make me consider latency problems first. I don’t see any use for anything but a regular USB cable. There is NO reason your normal single USB 2 cable shouldn’t function properly.
Might want to find a friend with RekordBox (or just with a fast laptop that he’ll let you install RB on) and try that with your controller. It would eliminate the laptop as the problem of the source if the symptoms persist.
Chuck Van EekelenModeratorWe have already had problems of folks buying old Vestax gear and not getting it working because it wasn’t the proper firmware and the new one was hard to fine if at all. This will only get worse as more and more things in OS and DJ software change.
Chuck Van EekelenModeratorBig can of worms. It’s why I always recommend using DMX software on a PC/Mac (like Cuelux) or on an iPad (Cuety). This gives you much more control than any single hardware controller.
That said, depending on the controller, you should be able to make a scene that plays both a chase for the lights and one for the laser. After all, a scene is nothing more than a collection of settings for your your fixtures (regardless of what they are).
That’s the theory anyway. Unfortunately DMX is to complicated to dive in without more (detailed) knowledge of the controller and the fixtures.
Chuck Van EekelenModeratorFor Traktor to RekordBox conversion you might look at:
Chuck Van EekelenModeratorAssuming you set everything correctly, this means the switch on the back for the RCA’s is set to main not booth, any RCA to mini-jack cable should do (providing it is a regular left+right RCA to stereo mini-jack).
It makes complete sense that you get headphone cues only when using the S2 for sound. Sometimes (not sure no Traktor anymore as I ditched it years ago) you can set the software so that main sound goes to one place (speakers through PC out) and headphones to your S2 for cueing. Still not an optimal way to go, not in the least because you can end up with different latencies.
The other thing that is wise to do, is to disconnect the Bose from USB so the only connection is the aux in on the control pad.
For testing purposes you an of course eliminate the cable as source by trying another one.
Also you can try borrowing a pair of active monitor speakers and hooking those up with the Bose fully disconnected and turned off. That would eliminate the Bose as source if you still have those noises.Personally I am no fan of using movie/gaming PC speakers for DJ-ing, period. Too often not a good match. Also price-wise you don’t have to. A pair of KRK 6s will run you about 270 euro as opposed to 400 for the Bose. And you can hook them up with balanced Jack-Jack cables which should normally eliminate any cable induced problems.
Should you need speakers that handle your other PC sound needs too, then I could suggest the Yamaha AG06 mixer. It has a built-in sound card, RCA’s for your RCA-RCA controller connection, an extra aux in (should you like to hook up iPad/iPhone or something) and lot’s of other features. If you play out in the future, it will be great for hooking up balanced PA speakers. You also get volume control right on your desktop. I have one sitting on my desk (well the smaller AG03) and I plug in my controller to the aux and my KRKs are connected Jack-Jack balanced.
Just my 3 cents as usual.
Chuck Van EekelenModeratorAn active sub only has an amp for the sub. The high-pass outputs just send the XLR signal on minus the very low frequencies. From there you either go into an amp and then to passive speakers (not what I would recommend) or to active speakers (often called “tops” or satellites).
So yeah, you would HAVE to place an amp between sub and passive speakers, but easier to use active speakers. Lot less cabling too.
Chuck Van EekelenModeratorHi Leon. Thanks for the introduction and welcome to the forums!
If you want to advance your DJ-ing to a level that will get you out playing in a short period of time, the How To Digital DJ Fast course could be for you. Check it out.
http://www.digitaldjtips.com/dj-courses/how-to-digital-dj-fast/
Chuck Van EekelenModeratorHi Anthony, welcome to the forums. Thanks for the introduction.
You ask some good questions that are not answered easily. DJ-ing at it’s very core is about “knowing what comes next”. And that is something that comes from deep knowledge of your collection (keeping it very tight, no need to fall in the “let’s collect any and all music I can get my hands on”-trap) and a very broad knowledge of what is out there (and preferably what has been out there that was successful).
Gear, technology and technical DJ skills come in distant 2nd.
As for how to make a good tape, you might want to invest in the Mixtape Pro Formula course that teaches you all you need to know to turn out good mixtapes.
As for the duration, most people don’t have time to listen to lengthy tapes. So, make a relatively short tape, showing a few tracks mixed into others that give an impression of the kind of music you think would be appropriate at this venue.
Good luck and enjoy your time here.
Chuck Van EekelenModeratorI am assuming they will do what they are supposed to. It being Pioneer you do pay for the brand name. A set of 6″ KRKs will cost you roughly the same as the 4″ DM40s. It’s a personal choice, I have KRK 5″ currently and if they have to be replaced I will go 6″, because the low end is just a bit lacking. This will be more the smaller the speaker. So the 4″ will have even less bass.
Chuck Van EekelenModeratorYour welcome. Good luck.
Chuck Van EekelenModeratorOne tip is to set all the options for the decks in advance in RekordBox and save those to your USB stick too. When you plug it in, it will ask if you want to load those personal settings. Say yes and all is well, repeat for other deck. That way you know both players have the same settings.
Chuck Van EekelenModeratorI am with Todd on this one. If you hook up your XDJs to your DJ software as well as your X1, you probably can pull it of, provided everything is mapped correctly.
Chuck Van EekelenModeratorNope, the link cable only works if the you have like a USB stick in one unit. Not when connected to DJ software.
-
AuthorPosts